 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 1 ?2000 integrated device technology, inc. dsc 2945/13 i/o control address decoder memory array arbitration semaphore logic address decoder i/o control r/ w l busy l a 13l a 0l 2945 drw 01 ub l lb l ce l oe l i/o 8l -i/o 15l i/o 0l -i/o 7l ce l sem l m/ s r/ w r busy r ub r lb r ce r oe r i/o 8r -i/o 15r i/o 0r -i/o 7r a 13r a 0r sem r ce r (1,2) (1,2) 14 14 idt70v26s/l high-speed 3.3v 16k x 16 dual-port static ram true dual-ported memory cells which allow simultaneous reads of the same memory location high-speed access ? commercial: 25/35/55ns (max.) low-power operation ? idt70v26s active: 300mw (typ.) standby: 3.3mw (typ.) ? idt70v26l active: 300mw (typ.) standby: 660 w (typ.) separate upper-byte and lower-byte control for multiplexed bus compatibility idt70v26 easily expands data bus width to 32 bits or more using the master/slave select when cascading more than one device m/ s = v ih for busy output flag on master m/ s = v il for busy input on slave on-chip port arbitration logic full on-chip hardware support of semaphore signaling between ports fully asynchronous operation from either port ttl-compatible, single 3.3v (0.3v) power supply available in 84-pin pga and plcc industrial temperature range (-40c to +85c) is available for selected speeds notes: 1. (master): busy is output; (slave): busy is input. 2. busy outputs are non-tri-stated push-pull. 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 2 the idt70v26 is a high-speed 16k x 16 dual-port static ram. the idt70v26 is designed to be used as a stand-alone 256k-bit dual- port ram or as a combination master/slave dual-port ram for 32- bit-or-more word systems. using the idt master/slave dual-port ram approach in 32-bit or wider memory system applications results in full-speed, error-free operation without the need for additional discrete logic. this device provides two independent ports with separate control, address, and i/o pins that permit independent, asynchronous access for reads or writes to any location in memory. an automatic power down feature controlled by ce permits the on-chip circuitry of each port to enter a very low standby power mode. fabricated using idt?s cmos high-performance technology, these devices typically operate on only 300mw of power. the idt70v26 is packaged in a ceramic 84-pin pga and 84-pin plcc. ! notes: 1. all v cc pins must be connected to power supply. 2. all gnd pins must be connected to ground supply. 3. package body is approximately 1.15 in x 1.15 in x .17 in. 4. this package code is used to reference the package diagram. 5. this text does not indicate orientation of the actual part-marking. 2945 drw 02 14 15 16 17 18 19 20 index 21 22 23 24 11109876543218483 33 34 35 36 37 38 39 40 41 42 43 44 45 v cc gnd i/o 8l a 8l 13 12 25 26 27 28 29 30 31 32 46 47 48 49 50 51 52 53 72 71 70 69 68 67 66 65 64 63 62 73 74 61 60 59 58 57 56 55 54 82 81 80 79 78 77 76 75 gnd busy l gnd idt70v26j j84-1 (4) 84-pin plcc top view (5) a 0l m/ s a 0r i/o 9l i/o 10l i/o 11l i/o 12l i/o 13l i/o 14l i/o 15l i/o 0r i/o 1r i/o 2r v cc i/o 3r i/o 4r i/o 5r i/o 6r i/o 7r i/o 8r a 7l a 6l a 5l a 4l a 3l a 2l a 1l busy r a 1r a 3r a 4r a 5r a 6r a 7r a 2r i / o 7 l i / o 6 l i / o 5 l i / o 4 l i / o 3 l i / o 2 l v c c r / w l s e m l c e l u b l l b l a 1 2 l g n d i / o 1 l i / o 0 l a 1 1 l a 1 0 l a 9 l o e l i / o 9 r i / o 1 0 r i / o 1 1 r i / o 1 2 r i / o 1 3 r i / o 1 4 r g n d i / o 1 5 r g n d a 1 2 r a 1 1 r a 1 0 r a 9 r a 8 r o e r r / w r s e m r c e r u b r l b r a 1 3 r a 1 3 l 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 3 notes: 1. all v cc pins must be connected to power supply. 2. all gnd pins must be connected to ground supply. 3. package body is approximately 1.12 in x 1.12 in x .16 in. 4. this package code is used to reference the package diagram. 5. this text does not indicate orientation of the actual part-marking. ! " #! left port right port names ce l ce r chip enable r/ w l r/ w r read/write enable oe l oe r output enable a 0l - a 13l a 0r - a 13r address i/o 0l - i/o 15l i/o 0r - i/o 15r data input/output sem l sem r semaphore enable ub l ub r upp er byte se lect lb l lb r lower byte select busy l busy r busy flag m/ s master or slave select v cc power gnd ground 2945 tbl 01 2945 drw 03 i/o 7l 63 61 60 58 55 54 51 48 46 45 66 67 69 72 75 76 79 81 82 83 125 7 8 11 10 12 14 17 20 23 26 28 29 32 31 33 35 38 41 43 idt70v26g g84-3 (4) 84-pin pga top view (5) abcdef ghj kl 42 59 56 49 50 40 25 27 30 36 34 37 39 843 4 6 9 15131618 22 24 19 21 68 71 70 77 80 ub r ce r gnd 11 10 09 08 07 06 05 04 03 02 01 64 65 62 57 53 52 47 44 73 74 78 gnd gnd r/ w r oe r lb r gnd gnd sem r ub l ce l r/ w l oe l gnd sem l v cc lb l a 13r busy r busy l m/ s a 13l a 11l index i/o 5l i/o 4l i/o 2l i/o 0l i/o 10l i/o 8l i/o 6l i/o 3l i/o 1l i/o 11l i/o 9l i/o 13l i/o 12l i/o 15l i/o 14l i/o 0r a 9l a 10l a 8l a 7l a 5l a 6l a 4l a 3l a 2l a 0l a 1l a 0r a 2r a 1r a 5r a 3r a 6r a 4r a 9r a 7r a 8r a 10r a 11r i/o 1r i/o 2r v cc i/o 3r i/o 4r i/o 5r i/o 7r i/o 6r i/o 9r i/o 8r i/o 11r i/o 10r i/o 12r i/o 13r i/o 14r i/o 15r v cc a 12r a 12l 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 4 $ %$ & ''() % * +,- ! $ %$ & '(. * +,- note: 1. a 0l ? a 13l a 0r ? a 13r note: 1. there are eight semaphore flags written to via i/o 0 and read from all i/o's (i/o 0 -i/o 15 ). these eight semaphores are addressed by a 0 -a 2 . inputs (1 ) outputs mode ce r/ w oe ub lb sem i/o 8-1 5 i/o 0-7 hxxxxhhigh-zhigh-zdeselected: power-down x x x h h h high-z high-z both bytes deselected: power-down llxlhhdata in high-z write to upper byte only l l x h l h high-z data in write to lower byte only llxllhdata in data in write to bo th by te s lhllhhdata out high-z read upper byte only lhlhlhhigh-zdata out read lower byte only lhlllhdata out data out read both bytes x x h x x x high-z high-z outputs disabled 2945 tbl 02 inputs (1 ) outputs mode ce r/ w oe ub lb sem i/o 8-15 i/o 0-7 hhlxx ldata out data out read data in semaphore flag xhlhhldata out data out read data in semaphore flag h xxxldata in data in write i/o 0 into semaphore flag x xhhldata in data in write i/o 0 into semaphore flag lxxlxl ____ ____ not allowed lxxxll ____ ____ not allowed 2945 tbl 03 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 5 /& 0 1 * ! 0 1 2 $ +) 34 ! * + +2 + ! ! $ / 5678 5 #09:! % 2; % 2 $ +) 34 * 4 5 # 4<# 4! notes: 1. stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. v term must not exceed vcc + 0.3v for more than 25% of the cycle time or 10ns maximum, and is limited to < 20ma for the period of v term > vcc + 0.3v. notes: 1. this is the parameter t a . this is the "instant on" case temperature. 2. industrial temperature: for specific speeds, packages and powers contact your sales office. notes: 1. v il > -1.5v for pulse width less than 10ns. 2. v term must not exceed vcc + 0.3v. notes: 1. this parameter is determined by device characterization but is not production tested. 2. 3dv represents the interpolated capacitance when the input and output signals switch from 0v to 3v or from 3v to 0v. note: 1. at v cc < 2.0v, input leakages are undefined. symbol rating commercial & industrial unit v te rm (2 ) terminal voltage with respect to gnd -0.5 to +4.6 v t bias temperature under bias -55 to +125 o c t stg storage temperature -65 to +150 o c i out dc output current 50 ma 2945 tbl 04 grade ambient temperature gnd vcc commercial 0 o c to +70 o c0v3.3v + 0.3 industrial -40 o c to +85 o c0v3.3v + 0.3 2 945 tb l 05 symbol parameter min. typ. max. unit v cc supply voltage 3.0 3.3 3.6 v gnd ground 0 0 0 v v ih input high voltage 2.0 ____ v cc + 0.3 (2 ) v v il input low voltage -0.3 (1 ) ____ 0.8 v 2945 tbl 06 symbol parameter conditions (2 ) max. unit c in input capacitance v in = 3dv 9 pf c out output capacitance v out = 3dv 10 pf 2945 tbl 07 symbol parameter test conditions 70v26s 70v26l unit min. max. min. max. |i li | input leakage current (1 ) v cc = 3.6v, v in = 0v to v cc ___ 10 ___ 5a |i lo | output leakage current ce = v ih , v out = 0v to v cc ___ 10 ___ 5a v ol output low voltage i ol = +4ma ___ 0.4 ___ 0.4 v v oh output high voltage i oh = -4ma 2.4 ___ 2.4 ___ v 2945 tbl 08 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 6 /$ + % 2; % 2 $ +) 34 * =! 4 5 # 4<# 4! notes: 1. 'x' in part number indicates power rating (s or l) 2. v cc = 3.3v, t a = +25 c, and are not production tested. i ccdc = 80ma (typ.) 3. at f = f max , address and control lines (except output enable) are cycling at the maximum frequency read cycle of 1/t rc, and using ? ac test conditions ? of input levels of gnd to 3v. 4. f = 0 means no address or control lines change. 5. port "a" may be either left or right port. port "b" is the opposite from port "a". 6. industrial temperature: for specific speeds, packages and powers contact your sales office. figure 1. ac output test load figure 2. output test load (for t lz , t hz , t wz , t ow ) * including scope and jig. 70v26x25 com'l only 70v26x35 com'l only 70v26x55 com'l only symbol parameter test condition version typ. (2 ) max. typ. (2 ) max. typ. (2 ) max. unit i cc dynamic operating current (both ports active) ce = v il , outputs disabled sem = v ih f = f max (3 ) com'l s l 100 100 170 140 90 90 140 120 90 90 140 120 ma ind s l ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ma i sb1 standby current (both ports - ttl level inputs) ce r = ce l = v ih sem r = sem l = v ih f = f max (3 ) com'l s l 14 12 30 24 12 10 30 24 12 10 30 24 ma ind s l ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ma i sb2 standby current (one port - ttl level inputs) ce "a " = v il and ce "b" = v ih (5 ) active port outputs disabled, f=f max (3 ) sem r = sem l = v ih com'l s l 50 50 95 85 45 45 87 75 45 45 87 75 ma ind s l ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ma i sb3 full standby current (both ports - cmos level inputs) both ports ce l and ce r > v cc - 0.2v, v in > v cc - 0.2v or v in < 0.2v, f = 0 (4 ) sem r = sem l > v cc - 0.2v com'l s l 1.0 0.2 6 3 1.0 0.2 6 3 1.0 0.2 6 3 ma ind s l ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ma i sb4 full standby current (one port - cmos level inputs) ce "a " < 0.2v and ce "b " > v cc - 0.2v (5 ) sem r = sem l > v cc - 0.2v v in > v cc - 0.2v or v in < 0.2v active port outputs disabled, f = f max (3 ) com'l s l 60 60 90 80 55 55 85 74 55 55 85 74 ma ind s l ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ma 2945 tbl 09 input pulse levels input rise/fall times input timing re fe renc e leve ls output reference levels output load gnd to 3.0v 3ns max. 1.5v 1.5v figures 1 and 2 2945 tbl 10 2945 drw 05 590 ? 30pf 435 ? 3.3v data out busy 590 ? 5pf* 435 ? 3.3v data out 2945 drw 04 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 7 notes: 1. transition is measured 0mv from low- or high-impedance voltage with output test load (figure 2). 2. this parameter is guaranteed by device characterization, but is not production tested. 3. to access ram, ce = v il and sem = v ih . to access semaphore, ce = v ih and sem = v il . 4. 'x' in part number indicates power rating (s or l). 5. industrial temperature: for specific speeds, packages and powers contact your sales office. / % 2; % 2 $ +) 34 * > 7! $ ? .? .? ce 2945 drw 06 t pu i cc i sb t pd 50% 50% , 70v26x25 com'l only 70v26x35 com'l only 70v26x55 com'l only unit symbol parameter min. max. min. max. min. max. read cycle t rc read cycle time 25 ____ 35 ____ 55 ____ ns t aa address access time ____ 25 ____ 35 ____ 55 ns t ace chip enable access time (3 ) ____ 25 ____ 35 ____ 55 ns t abe byte enable access time (3 ) ____ 25 ____ 35 ____ 55 ns t aoe output enable access time ____ 15 ____ 20 ____ 30 ns t oh output hold from address change 3 ____ 3 ____ 3 ____ ns t lz output low-z time (1,2) 3 ____ 3 ____ 3 ____ ns t hz output high-z time (1,2) ____ 15 ____ 20 ____ 25 ns t pu chip enable to power up time (2 ) 0 ____ 0 ____ 0 ____ ns t pd chip disable to power down time (2 ) ____ 25 ____ 35 ____ 50 ns t sop semaphore flag update pulse ( oe or sem )15 ____ 15 ____ 15 ____ ns t saa semaphore address access time ____ 35 ____ 45 ____ 65 ns 2945 tbl 11 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 8 - ; * +3 7! notes: 1. timing depends on which signal is asserted last, oe , ce , lb , or ub . 2. timing depends on which signal is de-asserted first ce , oe , lb , or ub . 3. t bdd delay is required only in cases where the opposite port is completing a write operation to the same address location. for simu ltaneous read operations busy has no relation to valid output data. 4. start of valid data depends on which timing becomes effective last t aoe , t ace , t aa or t bdd . 5. sem = v ih . notes: 1. transition is measured 0mv from low- or high-impedance voltage with output test load (figure 2). 2. this parameter is guaranteed by device characterization, but is not production tested. 3. to access ram, ce = v il and sem = v ih . to access semaphore, ce = v ih and sem = v il . either condition must be valid for the entire t ew time. 4. the specification for t dh must be met by the device supplying write data to the ram under all operating conditions. although t dh and t ow values will vary over voltage and temperature, the actual t dh will always be smaller than the actual t ow . 5. 'x' in part numbers indicates power rating (s or l). 6. industrial temperature: for specific speeds, packages and powers contact your sales office. / % 2; % 2 $ +) 34 7 =! t rc r/ w ce addr t aa oe ub , lb 2945 drw 07 (4) t ace (4) t aoe (4) t abe (4) (1) t lz t oh (2) t hz (3,4) t bdd data out busy out valid data (4) symbol parameter 70v26x25 com'l only 70v26x35 com'l only 70v26x55 com'l only unit min. max. min. max. min. max. write cycle t wc write cycle time 25 ____ 35 ____ 55 ____ ns t ew chip enable to end-of-write (3 ) 20 ____ 30 ____ 45 ____ ns t aw address valid to end-of-write 20 ____ 30 ____ 45 ____ ns t as address set-up time (3 ) 0 ____ 0 ____ 0 ____ ns t wp write pulse width 20 ____ 25 ____ 40 ____ ns t wr write recovery time 0 ____ 0 ____ 0 ____ ns t dw data valid to end-of-write 15 ____ 20 ____ 30 ____ ns t hz output high-z time (1,2) ____ 15 ____ 20 ____ 25 ns t dh data ho ld time (4 ) 0 ____ 0 ____ 0 ____ ns t wz write enabl e to output in hig h-z (1,2) ____ 15 ____ 20 ____ 25 ns t ow output active from end -of-write (1 , 2 ,4 ) 0 ____ 0 ____ 0 ____ ns t swrd sem flag write to read time 5 ____ 5 ____ 5 ____ ns t sps sem flag contention window 5 ____ 5 ____ 5 ____ ns 2945 tbl 12 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 9 $- ; - 3 # *, w +$ 7 @! notes: 1. r/ w or ce or ub and lb must be high during all address transitions. 2. a write occurs during the overlap (t ew or t wp ) of a low ce and a low r/ w for memory array writing cycle. 3. t wr is measured from the earlier of ce or r/ w (or sem or r/ w ) going high to the end of write cycle. 4. during this period, the i/o pins are in the output state and input signals must not be applied. 5. if the ce or sem low transition occurs simultaneously with or after the r/ w low transition, the outputs remain in the high-impedance state. 6. timing depends on which enable signal is asserted last, ce or r/ w . 7. this parameter is guaranteed by device characterization, but is not production tested. transition is measured 0mv from steady state with the output test load (figure 2). 8. if oe is low during r/ w controlled write cycle, the write pulse width must be the larger of t wp or (t wz + t dw ) to allow the i/o drivers to turn off and data to be placed on the bus for the required t dw . if oe is high during an r/ w controlled write cycle, this requirement does not apply and the write pulse can be as short as the specified t wp . 9. to access ram, ce = v il and sem = v ih . to access semaphore, ce = v ih and sem = v il . t ew must be met for either condition. $- ; - 3 # ce ub lb +$ 7! r/ w t wc t hz t aw t wr t as t wp data out (2) t wz t dw t dh t ow oe address data in (6) (4) (4) (7) ce or sem 2945 drw 08 (9) ce or sem (9) (7) (3) 2945 drw 09 t wc t as t wr t dw t dh address data in r/ w t aw t ew ub or lb (3) (2) (6) ce or sem (9) (9) 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 10 $- ; ) % * + - $ % )+ ! notes: 1. d or = d ol = v il , ce r = ce l = v ih , or both ub & lb = v ih . 2. all timing is the same for left and right ports. port ? a ? may be either left or right port. port ? b ? is the opposite from port ? a ? . 3. this parameter is measured from r/ w " a" or sem " a" going high to r/ w " b" or sem " b" going high. 4. if t sps is not satisfied, the semaphore will fall positively to one side or the other, but there is no guarantee which side will obtai n the flag. $- ; ) % - >! notes: 1. ce = v ih or ub & lb = v ih for the duration of the above timing (both write and read cycle). 2. "data out valid' represents all i/o's (i/o 0 -i/o 15 ) equal to the semaphore value. sem 2945 drw 10 t aw t ew t sop i/o 0 valid address t saa r/ w t wr t oh t ace valid address data in valid data out t dw t wp t dh t as t swrd t aoe read cycle write cycle a 0 -a 2 oe valid (2) sem "a" 2945 drw 11 t sps match r/ w "a" match a 0"a" -a 2"a" side "a" (2) sem "b" r/ w "b" a 0"b" -a 2"b" side (2) "b" 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 11 2945 drw 12 t dw t aps addr "a" t wc data out "b" match t wp r/ w "a" data in "a" addr "b" t dh valid (1) match busy "b" t bda valid t bdd t ddd (3) t wdd t baa / % 2; % 2 $ +) 34 * = a! notes: 1. port-to-port delay through ram cells from writing port to reading port, refer to "timing waveform of write with port-to-port read and busy (m/ s = v ih )". 2. to ensure that the earlier of the two ports wins. 3. t bdd is a calculated parameter and is the greater of 0, t wdd ? t wp (actual) or t ddd ? t dw (actual). 4. to ensure that the write cycle is inhibited on port "b" during contention on port "a". 5. to ensure that a write cycle is completed on port "b" after contention on port "a". 6. 'x' in part number indicates power rating (s or l). 7. industrial temperature: for specific speeds, packages and powers contact your sales office. $- ; - ? % . . * + + busy > 7! notes: 1. to ensure that the earlier of the two ports wins. t aps is ignored for m/ s = v il (slave). 2. ce l = ce r = v il 3. oe = v il for the reading port. 4. if m/ s = v il (slave), then busy is an input ( busy "a" = v ih and busy "b" = "don't care", for this example). 5. all timing is the same for left and right ports. port "a" may be either the left or right port. port "b" is the port opposite from port "a". 70v26x25 com'l only 70v26x35 com'l only 70v26x55 com'l only symbol parameter min. max. min. max. min. max. unit busy timing (m/ s = v ih ) t baa busy access time from address match ____ 25 ____ 35 ____ 45 ns t bda busy disable time from address not match ____ 25 ____ 35 ____ 45 ns t bac busy access time from chip enable low ____ 25 ____ 35 ____ 45 ns t bdc busy disab le time from chip enable high ____ 25 ____ 35 ____ 45 ns t aps arbitration priority set-up time (2 ) 5 ____ 5 ____ 5 ____ ns t bdd busy disable to valid data (3 ) ____ 35 ____ 40 ____ 50 ns t wh write hold after busy (5 ) 20 ____ 25 ____ 25 ____ ns busy input timing (m/ s = vil) t wb busy input to write (4 ) 0 ____ 0 ____ 0 ____ ns t wh write hold after busy (5 ) 20 ____ 25 ____ 25 ____ ns port-to-port delay timing t wdd write pulse to data delay (1 ) ____ 55 ____ 65 ____ 85 ns t ddd write data valid to read data delay (1 ) ____ 50 ____ 60 ____ 80 ns 2945 tbl 13 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 12 $- ; - ? % busy notes: 1. all timing is the same for left and right ports. port ? a ? may be either the left or right port. port ? b ? is the port opposite from port ? a ? . 2. if t aps is not satisfied, the busy signal will be asserted on one side or the other, but there is no guarantee on which side busy will be asserted. - ; busy / & +&3 ce $ ! notes: 1. t wh must be met for both busy input (slave) and output (master). 2. busy is asserted on port "b" blocking r/ w "b" , until busy "b" goes high. - ; busy / & 3 +&3/++ 0 %$ ! 2945 drw 13 r/ w "a" busy "b" t wp t wb r/ w "b" t wh (1) (2) 2945 drw 14 addr "a" and "b" addresses match ce "a" ce "b" busy "b" t aps t bac t bdc (2) 2945 drw 15 addr "a" address "n" addr "b" busy "b" t aps t baa t bda (2) matching address "n" 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 13 the idt70v26 provides two ports with separate control, address and i/o pins that permit independent access for reads or writes to any location in memory. the idt70v26 has an automatic power down feature controlled by ce . the ce controls on-chip power down circuitry that permits the respective port to go into a standby mode when not selected ( ce high). when a port is enabled, access to the entire memory array is permitted. 3b busy logic provides a hardware indication that both ports of the ram have accessed the same location at the same time. it also allows one of the two accesses to proceed and signals the other side that the ram is ? busy ? . the busy pin can then be used to stall the access until the operation on the other side is completed. if a write operation has been attempted from the side that receives a busy indication, the write signal is gated internally to prevent the write from proceeding. the use of busy logic is not required or desirable for all applica- tions. in some cases it may be useful to logically or the busy outputs together and use any busy indication as an interrupt source to flag an illegal or illogical operation. if the write inhibit function of busy logic is not desirable, the busy logic can be disabled by placing the part in slave mode with the m/ s pin. once in slave mode the busy pin operates solely as a write inhibit input pin. normal operation can be programmed by tying the busy pins high. if desired, unintended notes: 1. pins busy l and busy r are both outputs when the part is configured as a master. both are inputs when configured as a slave. busy x outputs on the idt70v26 are push pull, not open drain outputs. on slaves the busy x input internally inhibits writes. 2. l if the inputs to the opposite port were stable prior to the address and enable inputs of this port. h if the inputs to the opposite port became stable after the address and enable inputs of this port. if t aps is not met, either busy l or busy r = low will result. busy l and busy r outputs cannot be low simultaneously. 3. writes to the left port are internally ignored when busy l outputs are driving low regardless of actual logic level on the pin. writes to the right port are internally ignored when busy r outputs are driving low regardless of actual logic level on the pin. $ %$ & '''(/++ busy / & $ %$ & '4(1 ) % ) c ! note: 1. this table denotes a sequence of events for only one of the eight semaphores on the idt70v26. 2. there are eight semaphore flags written to via i/o 0 and read from all i/o's (i/o 0 -i/o 15 ). these eight semaphores are addressed by a 0 -a 2 . 3. ce = v ih , sem = v il to access the semaphores. refer to the semaphore read/write control truth table. inputs outputs function ce l ce r a 0l -a 13l a 0r -a 13r busy l (1 ) busy r (1 ) xxno match h h normal h x match h h normal x h match h h normal l l match (2) (2) write inhibit (3 ) 2945 tbl 14 functions d 0 - d 15 left d 0 - d 15 right status no action 1 1 semaphore free left port writes "0" to semaphore 0 1 left port has semaphore token right port writes "0" to semaphore 0 1 no change. right side has no write access to semaphore left port writes "1" to semaphore 1 0 right port obtains semaphore token left port writes "0" to semaphore 1 0 no change. left port has no write access to semaphore right port writes "1" to semaphore 0 1 left port obtains semaphore token left port writes "1" to semaphore 1 1 semaphore free right port writes "0" to semaphore 1 0 right port has semaphore token right port writes "1" to semaphore 1 1 semaphore free left port writes "0" to semaphore 0 1 left port has semaphore token left port writes "1" to semaphore 1 1 semaphore free 2945 tbl 15 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 14 write operations can be prevented to a port by tying the busy pin for that port low. the busy outputs on the idt 70v26 ram in master mode, are push-pull type outputs and do not require pull up resistors to operate. if these rams are being expanded in depth, then the busy indication for the resulting array requires the use of an external and gate. -+ %1 ? % busy b 0 ,) ; / 3 when expanding an idt70v26 ram array in width while using busy logic, one master part is used to decide which side of the ram array will receive a busy indication, and to output that indication. any are completely independent of each other. this means that the activity on the left port in no way slows the access time of the right port. both ports are identical in function to standard cmos static ram and can be read from, or written to, at the same time with the only possible conflict arising from the simultaneous writing of, or a simultaneous read/write of, a non-semaphore location. semaphores are pro- tected against such ambiguous situations and may be used by the system program to avoid any conflicts in the non-semaphore portion of the dual-port sram. these devices have an automatic power- down feature controlled by ce , the dual-port sram enable, and sem , the semaphore enable. the ce and sem pins control on-chip power down circuitry that permits the respective port to go into standby mode when not selected. this is the condition which is shown in truth table i where ce and sem are both high. systems which can best use the idt70v26 contain multiple processors or controllers and are typically very high-speed systems which are software controlled or software intensive. these systems can benefit from a performance increase offered by the idt70v26's hardware semaphores, which provide a lockout mechanism without requiring complex programming. software handshaking between processors offers the maximum in system flexibility by permitting shared resources to be allocated in varying configurations. the idt70v26 does not use its semaphore flags to control any resources through hardware, thus allowing the system designer total flexibility in system architecture. an advantage of using semaphores rather than the more common methods of hardware arbitration is that wait states are never incurred in either processor. this can prove to be a major advantage in very high-speed systems. 9? % ) % - the semaphore logic is a set of eight latches which are indepen- dent of the dual-port sram. these latches can be used to pass a flag, or token, from one port to the other to indicate that a shared resource is in use. the semaphores provide a hardware assist for a use assignment method called ? token passing allocation. ? in this method, the state of a semaphore latch is used as a token indicating that shared resource is in use. if the left processor wants to use this resource, it requests the token by setting the latch. this processor then verifies its success in setting the latch by reading it. if it was successful, it proceeds to assume control over the shared resource. if it was not successful in setting the latch, it determines that the right side processor has set the latch first, has the token and is using the shared resource. the left processor can then either repeatedly request that semaphore ? s status or remove its request for that semaphore to perform another task and occasionally attempt again to gain control of the token via the set and test sequence. once the right side has relinquished the token, the left side should succeed in gaining control. the semaphore flags are active low. a token is requested by writing a zero into a semaphore latch and is released when the same side writes a one to that latch. the eight semaphore flags reside within the idt70v26 in a separate memory space from the dual-port sram. this address space is accessed by placing a low input on the sem pin (which acts as a chip select for the semaphore flags) and using the other control pins (address, oe , and r/ w ) as they would be used in accessing a figure 3. busy and chip enable routing for both width and depth expansion with idt70v26 rams. number of slaves to be addressed in the same address range as the master use the busy signal as a write inhibit signal. thus on the idt70v26 sram the busy pin is an output if the part is used as a master (m/ s pin = h), and the busy pin is an input if the part used as a slave (m/ s pin = l) as shown in figure 3. if two or more master parts were used when expanding in width, a split decision could result with one master indicating busy on one side of the array and another master indicating busy on one other side of the array. this would inhibit the write operations from one port for part of a word and inhibit the write operations from the other port for word. the busy arbitration, on a master, is based on the chip enable and address signals only. it ignores whether an access is a read or write. in a master/slave array, both address and chip enable must be valid long enough for a busy flag to be output from the master before the actual write pulse can be initiated with either the r/ w signal or the byte enables. failure to observe this timing can result in a glitched internal write inhibit signal and corrupted data in the slave. ) % the idt70v26 is an extremely fast dual-port 16k x 16 cmos static ram with an additional 8 address locations dedicated to binary semaphore flags. these flags allow either processor on the left or right side of the dual-port sram to claim a privilege over the other processor for functions defined by the system designer ? s software. as an example, the semaphore can be used by one processor to inhibit the other from accessing a portion of the dual-port sram or any other shared resource. the dual-port sram features a fast access time, and both ports 2945 drw 16 master dual port ram busy l busy r ce master dual port ram busy l busy r ce slave dual port ram busy l busy r ce slave dual port ram busy l busy r ce busy l busy r d e c o d e r 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 15 standard static ram. each of the flags has a unique address which can be accessed by either side through address pins a 0 ? a 2 . when accessing the semaphores, none of the other address pins has any effect. when writing to a semaphore, only data pin d 0 is used. if a low level is written into an unused semaphore location, that flag will be set to a zero on that side and a one on the other side (see truth table iv). that semaphore can now only be modified by the side showing the zero. when a one is written into the same location from the same side, the flag will be set to a one for both sides (unless a semaphore request from the other side is pending) and then can be written to by both sides. the fact that the side which is able to write a zero into a semaphore subsequently locks out writes from the other side is what makes semaphore flags useful in interprocessor communications. (a thor- ough discussion on the use of this feature follows shortly.) a zero written into the same location from the other side will be stored in the semaphore request latch for that side until the semaphore is freed by the first side. when a semaphore flag is read, its value is spread into all data bits so that a flag that is a one reads as a one in all data bits and a flag containing a zero reads as all zeros. the read value is latched into one side ? s output register when that side's semaphore select ( sem ) and output enable ( oe ) signals go active. this serves to disallow the semaphore from changing state in the middle of a read cycle due to a write cycle from the other side. because of this latch, a repeated read of a semaphore in a test loop must cause either signal ( sem or oe ) to go inactive or the output will never change. a sequence write/read must be used by the semaphore in order to guarantee that no system level contention will occur. a processor requests access to shared resources by attempting to write a zero into a semaphore location. if the semaphore is already in use, the semaphore request latch will contain a zero, yet the semaphore flag will appear as one, a fact which the processor will verify by the subsequent read (see truth table iv). as an example, assume a processor writes a zero to the left port at a free semaphore location. on a subsequent read, the processor will verify that it has written success- fully to that location and will assume control over the resource in question. meanwhile, if a processor on the right side attempts to write a zero to the same semaphore flag it will fail, as will be verified by the fact that a one will be read from that semaphore on the right side during subsequent read. had a sequence of read/write been used instead, system contention problems could have occurred during the gap between the read and write cycles. it is important to note that a failed semaphore request must be followed by either repeated reads or by writing a one into the same location. the reason for this is easily understood by looking at the simple logic diagram of the semaphore flag in figure 4. two sema- phore request latches feed into a semaphore flag. whichever latch is first to present a zero to the semaphore flag will force its side of the semaphore flag low and the other side high. this condition will continue until a one is written to the same semaphore request latch. should the other side ? s semaphore request latch have been written to a zero in the meantime, the semaphore flag will flip over to the other side as soon as a one is written into the first side ? s request latch. the second side ? s flag will now stay low until its semaphore request latch is written to a one. from this it is easy to understand that, if a semaphore is requested and the processor which requested it no longer needs the resource, the entire system can hang up until a one is written into that semaphore request latch. the critical case of semaphore timing is when both sides request a single token by attempting to write a zero into it at the same time. the semaphore logic is specially designed to resolve this problem. if simultaneous requests are made, the logic guarantees that only one side receives the token. if one side is earlier than the other in making the request, the first side to make the request will receive the token. if both requests arrive at the same time, the assignment will be arbitrarily made to one port or the other. one caution that should be noted when using semaphores is that semaphores alone do not guarantee that access to a resource is secure. as with any powerful programming technique, if semaphores are misused or misinterpreted, a software error can easily happen. initialization of the semaphores is not automatic and must be handled via the initialization program at power-up. since any sema- phore request flag which contains a zero must be reset to a one, all semaphores on both sides should have a one written into them at initialization from both sides to assure that they will be free when needed. ) % () 1 perhaps the simplest application of semaphores is their applica- tion as resource markers for the idt70v26 ? s dual-port ram. say the 16k x 16 ram was to be divided into two 8k x 16 blocks which were to be dedicated at any one time to servicing either the left or right port. semaphore 0 could be used to indicate the side which would control the lower section of memory, and semaphore 1 could be defined as the indicator for the upper section of memory. to take a resource, in this example the lower 8k of dual-port ram, the processor on the left port could write and then read a zero in to semaphore 0. if this task were successfully completed (a zero was read back rather than a one), the left processor would assume control of the lower 8k. meanwhile the right processor was attempting to gain control of the resource after the left processor, it would read back a one in response to the zero it had attempted to write into semaphore 0. at this point, the software could choose to try and gain control of the second 8k section by writing, then reading a zero into semaphore 1. if it succeeded in gaining control, it would lock out the left side. once the left side was finished with its task, it would write a one to semaphore 0 and may then try to gain access to semaphore 1. if semaphore 1 was still occupied by the right side, the left side could figure 4. idt70v26 semaphore logic d 2945 drw 17 0 d q write d 0 d q write semaphore request flip flop semaphore request flip flop lport rport semaphore read semaphore read , 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 16 undo its semaphore request and perform other tasks until it was able to write, then read a zero into semaphore 1. if the right processor performs a similar task with semaphore 0, this protocol would allow the two processors to swap 8k blocks of dual-port ram with each other. the blocks do not have to be any particular size and can even be variable, depending upon the complexity of the software using the semaphore flags. all eight semaphores could be used to divide the dual-port ram or other shared resources into eight parts. sema- phores can even be assigned different meanings on different sides rather than being given a common meaning as was shown in the example above. semaphores are a useful form of arbitration in systems like disk interfaces where the cpu must be locked out of a section of memory during a transfer and the i/o device cannot tolerate any wait states. with the use of semaphores, once the two devices has determined which memory area was ? off-limits ? to the cpu, both the cpu and the i/o devices could access their assigned portions of memory continu- ously without any wait states. semaphores are also useful in applications where no memory ? wait ? state is available on one or both sides. once a semaphore handshake has been performed, both processors can access their assigned ram segments at full speed. another application is in the area of complex data structures. in this case, block arbitration is very important. for this application one processor may be responsible for building and updating a data structure. the other processor then reads and interprets that data structure. if the interpreting processor reads an incomplete data structure, a major error condition may exist. therefore, some sort of arbitration must be used between the two different processors. the building processor arbitrates for the block, locks it and then is able to go in and update the data structure. when the update is completed, the data structure block is released. this allows the interpreting processor to come back and read the complete data structure, thereby guaran- teeing a consistent data structure. 6.42 idt70v26s/l high-speed 16k x 16 dual-port static ram industrial and commercial temperature rang es 17 2 + ' note: 1. industrial temperature range is available. for specific speeds, packages and powers contact your sales office. 2945 drw 18 a power 999 speed a package a process/ temperature range blank i (1) commercial (0 cto+70 c) industrial (-40 cto+85 c) g j 84-pin pga (g84-3) 84-pin plcc (j84-1) 25 35 55 s l standard power low power xxxxx device type 256k (16k x 16) 3.3v dual-port ram 70v26 idt speed in nanoseconds commercial only commercial only commercial only the idt logo is a registered trademark of integrated device technology, inc. % 9 3 3/25/99: initiated datasheet document history converted to new format cosmetic and typographical corrections page 2 and 3 added additional notes to pin configurations 6/10/99: changed drawing format 8/6/99: page 1 removed preliminary 8/30/99: page 1 changed 660mw to 660 w 11/12/99: replaced idt logo 6/6/00: page 5 increased storage temperature parameter clarified t a parameter page 6 dc electrical parameters ? changed wording from "open" to "disabled" changed 200mv to 0mv in notes corporate headquarters for sales: for tech support: 2975 stender way 800-345-7015 or 408-727-6116 831-754-4613 santa clara, ca 95054 fax: 408-492-8674 dualporthelp@idt.com www.idt.com |
Price & Availability of IDT70V26L55GI
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |